How to Disable Viper Car Alarm Permanently

If your Viper car alarm is giving you problems, you may be wondering how to disable it permanently. Luckily, there are a few things you can do to turn off your alarm and get it out of your life for good. First, try disconnecting the battery.

This will usually stop the alarm from going off. If that doesn’t work, you can try removing the fuse that controls the alarm.

  • Open the hood of your car and locate the alarm’s brain, which is usually mounted near the firewall on the driver’s side
  • Unplug the alarm’s brain from its power source, which is typically a red and black wire
  • Use a pair of needle-nose pliers to remove the ground wire from the alarm’s brain
  • The ground wire is usually black
  • Tape over or otherwise disable the alarm’s siren, which is usually located near the front of the vehicle on the driver’s side
  • Close up your car and test it out to make sure that the alarm is no longer functional

How to disable Viper alarm

How to Disable Viper Car Alarm Without Remote

If your Viper car alarm is giving you trouble, you may be wondering how to disable it without the remote. Here are a few steps you can take to disable your Viper car alarm: 1. Locate the alarm’s brain.

This is usually located in the engine bay, near the battery. 2. Disconnect the brain from the vehicle’s electrical system. You will likely need to remove a few bolts to do this.

3. Once the brain is disconnected, find the fuse that powers it and remove it. This will disable the alarm completely. 4. If you want to be extra safe, you can also disconnect the siren from its power source.

This will ensure that even if someone does manage to reconnect the brain, they won’t be able to make any noise with it!

How to Disable Viper Car Alarm Permanently


How Do I Permanently Disconnect My Car Alarm?

Most car alarms can be permanently disconnected by removing the fuse that powers the alarm. The location of the fuse will vary depending on your vehicle make and model, but it is usually located in the engine bay or under the dash. Once you have found and removed the fuse, your car alarm should be permanently disabled.

Where is the Valet Switch Located on a Viper Alarm?

If you’re looking for the valet switch on a Viper alarm, you’ll find it on the control module. The control module is typically located under the dash, near the steering column. On some models, it may be located in the glove box or center console.

Does Disconnecting a Car Battery Disable the Alarm?

If you disconnect the battery from your car, it will disable the alarm. The alarm system in your car is connected to the battery, and when you disconnect the battery, it severs that connection. This means that the alarm will no longer be able to function even if someone tries to break into your car or tamper with it in some way.

While this may provide you with a sense of security, it’s important to remember that there are other ways for a determined thief to break into your car. So don’t rely on this method alone to protect your vehicle.

How Do You Turn off an Aftermarket Car Alarm Without the Remote?

If you have an aftermarket car alarm and you’ve lost or misplaced your remote, don’t despair—you can usually disable the alarm without it. Here’s how: First, check to see if your car alarm has a backup battery.

If so, simply disconnect the battery to disable the alarm. If there is no backup battery, you’ll need to find the main power wire for the alarm system and disconnect it. This wire is usually red and is located near the fuse box in your vehicle.

Once you’ve found it, use a pair of pliers to twist the wire until it breaks, then tuck any loose ends out of sight. With the power disconnected, the final step is to remove any sensors that may be triggering the alarm (e.g., door sensors, motion sensors). Once all sensors are removed, your aftermarket car alarm should be disabled.


Viper car alarm systems are known for their reliability and effectiveness. However, some users may want to disable their Viper car alarm system permanently. This can be done by following a few simple steps.

First, the user will need to locate the control module for the Viper car alarm system. This is usually located under the hood or in the trunk of the vehicle. Next, the user will need to disconnect the battery terminals from the control module.

Finally, the user will need to remove the fuses that power the Viper car alarm system.

Leave a Comment

Your email address will not be published. Required fields are marked *