How to Fix Hyper Flash

If your car is hyper flashing when you turn on the blinkers, it could be a sign that the bulbs are going bad. In order to fix this, you will need to replace the bulbs with new ones. You can do this by opening up the hood and finding the old bulbs.

Once you have found them, twist them out and put in new bulbs. Be sure to check that they are tight before closing the hood.

  • If your car has hyper flash, it means that the turn signal is flashing too fast
  • This can be caused by a few different things
  • First, check to see if all the bulbs in your turn signal are working
  • If one of them is burned out, it will cause the others to flash faster
  • Next, check the fuse for your turn signals
  • If it is blown, replace it with a new one of the same amperage
  • Finally, if neither of those solutions work, there may be something wrong with the wiring in your car’s turn signal system
  • You’ll need to consult a professional mechanic or auto electrician to diagnose and fix the problem

LED Turn Signal Bulbs Hyper Flash /Error Code [How to Fix]

How to Fix Hyper Flash Without Resistor

If your car has hyper flash, it means that the turn signal is flashing faster than usual. This is usually caused by a problem with the bulb or the wiring. In most cases, you can fix this problem without having to buy a new bulb or a resistor.

Here’s how: First, check the bulb to make sure it is not burned out. If it is, replace it with a new one.

Next, check the wiring to see if there are any loose connections. If so, tighten them up or replace the wires altogether. Finally, if neither of these solutions work, you may need to buy a new turn signal switch.

This can be found at your local auto parts store.

How to Fix Hyper Flash


How Do I Get Rid of Led Hyper Flash?

If your car has LED Tail Lights, you may have experienced the “hyper flash” phenomenon. This is when the turn signal appears to be flashing faster than usual, and is caused by a difference in the electrical current required by LEDs and incandescent bulbs. There are a few ways to fix this problem:

1. Use a Load Resistor: A load resistor is placed in line with the LED tail light and creates additional resistance, which fools the turn signal into thinking it has a regular incandescent bulb installed. 2. Install a Flash Relay: A flash relay bypasses the car’s existing flasher unit and tricks it into thinking there’s an incandescent bulb installed. 3. Use LED-Compatible Flasher Units: Some aftermarket flasher units are designed specifically for use with LED lights and will eliminate hyper flashing.

What Causes Hyper Flashing?

Hyper flashing is a common problem that can occur when upgrading your car’s headlights to LED bulbs. The problem occurs when the new LED bulbs draw less power than the factory halogen bulbs, causing the turn signal relay to think there is a bulb failure. This will cause the turn signals to flash faster than normal, or in some cases, not at all.

There are a few ways to fix this problem: 1. Use a load resistor: This is the most common and effective solution. Load resistors are placed in line with the LED bulbs and mimic the power draw of a factory halogen bulb.

This will fool the turn signal relay into thinking everything is working correctly and allow it to operate at its normal speed. 2. Use a diode kit: A diode kit works by redirecting some of the power from the brake light circuit back into the turn signal circuit, giving it enough power to function properly. This solution is less common but can be just as effective as using load resistors.

3. Upgrade your turn signal relay: If you’re still having problems after trying one of the previous solutions, you may need to upgrade your turn signal relay to one that is designed for use with LED bulbs.

How Do You Fix a Fast Blinking Led Turn Signal?

Assuming you are referring to a car’s turn signal, there are a few things that could be causing the issue. The most common cause is a burnt out bulb. If this is the case, simply replacing the bulb should fix the problem.

If the bulbs are not burnt out, then there could be an issue with the wiring or connection. This will require some troubleshooting to figure out where the problem lies. First, check all of the connections and make sure they are tight and free of corrosion.

If everything looks good there, then you may need to trace the wires to see if there is a break or loose connection somewhere along the way. Fixing a fast blinking LED turn signal can be a simple fix or a more complicated one depending on what is causing the issue. By troubleshooting and ruling out each potential problem, you should be able to narrow down and fix the real issue.

How Do You Install a Resistor for Hyper Flash?

Installing a resistor for hyper flash is a simple process that can be completed in a few minutes. First, locate the positive and negative wires coming from the turn signal bulb. Next, connect one end of the resistor to the positive wire and the other end to the negative wire.

Finally, test the turn signal to make sure it is functioning properly.


If your car’s turn signal is flashing too fast, it’s called hyper flash. This is usually caused by a burned-out bulb, but it can also be caused by a problem with the wiring or the flasher unit itself. Here’s how to fix it:

1. Check the bulbs first. If one of them is burned out, replace it and see if that fixes the problem. 2. If not, then check the wiring.

Look for any bare wires or frayed insulation. If you find anything, repair or replace the damaged sections of wire. 3. If the wiring looks good, then the problem is probably with the flasher unit itself.

You can buy a new one at most auto parts stores; just make sure to get one that’s compatible with your car’s electrical system.

Leave a Comment

Your email address will not be published. Required fields are marked *