How to Remove Molded Body Kit

Assuming you want to remove a molded body kit: First, you’ll need to gather some supplies. You’ll need gloves, rubbing alcohol, a soft cloth or sponge, and a putty knife.

Next, use the putty knife to gently scrape away any loose molding. Be careful not to damage the underlying surface. Once all the loose molding has been removed, soak the area with rubbing alcohol.

This will help break down the mold and make it easier to remove. Finally, use the soft cloth or sponge to scrub away the remaining mold. Rinse with clean water and dry thoroughly.

  • Begin by thoroughly cleaning the area around the molding with soap and water
  • Next, use a putty knife or similar tool to pry the molding away from the body of the car
  • Once you have removed the molding, use a clean cloth to wipe away any residue that may be left behind
  • Finally, use a new piece of molding to replace the old one, and secure it in place with adhesive or tape

How to Remove Body Kit from Car

Removing a body kit from a car is not difficult, but it does require some time and patience. The first step is to remove all the screws that hold the kit in place. Next, gently pry the kit away from the car body, being careful not to damage the paint.

Once the kit is loose, carefully pull it off of the car. If necessary, use a putty knife or other sharp object to help loosen stubborn pieces. Finally, clean any adhesive residue off of the car body and enjoy your new look!

How to Remove Molded Body Kit


Can You Undo a Widebody Kit?

If you have a widebody kit installed on your car, you can undo it and return your car to its original state. However, the process is not easy and will require some work. You will need to remove the fenders, doors, and other panels that make up the kit.

Once these are removed, you will need to sand down the paint job and primer that was used to install the kit. This can be a difficult and time-consuming task, but it is possible to undo a widebody kit.

How Do You Remove Fibreglass from a Car?

If you’re looking to remove fibreglass from your car, there are a few things you’ll need to do. First, you’ll need to gather some supplies. You’ll need gloves, eye protection, a putty knife, and sandpaper.

Once you have your supplies, follow these steps: 1. Put on your gloves and eye protection. 2. Use the putty knife to scrape away as much of the fibreglass as possible.

3. Once you’ve removed as much as you can with the putty knife, use sandpaper to sand down the remaining fibreglass until it’s smooth. 4. Wash the area with soap and water to remove any debris or residue.

How Do You Reinforce a Fiberglass Body Kit?

If you’re looking to reinforce your fiberglass body kit, there are a few things you can do. One is to add more layers of fiberglass matting. This will help to thicken and strengthen the overall structure.

Another option is to use epoxy resin, which will create a stronger bond between the fibers. You can also use metal reinforcement bars or plates in strategic areas to add extra strength and rigidity.

Removing a Molded in Fiberglass Body Kit from our CRX Rust to Finished – GT Canada CRX Project Ep 3


Removing a molded body kit can be a difficult and time-consuming task. However, with the proper tools and techniques, it can be done relatively easily. First, you will need to gather the following materials: soap, water, bleach, a stiff brush, and gloves.

Next, you will need to mix one part bleach with ten parts water in a bucket. Once mixed together well, begin scrubbing the moldy areas of the body kit with the brush. Be sure to wear gloves while doing this.

Continue scrubbing until all of the mold is removed. Once the mold is gone, rinse off the area with clean water and dry it completely. If necessary, apply another round of bleach solution and repeat the process until all traces of mold are gone.

Finally, wash the area with soap and water to remove any residual bleach before applying new paint or primer.

Leave a Comment

Your email address will not be published. Required fields are marked *