How to Remove Purge Valve Clips

If your car has a purge valve, it’s there to prevent fuel vapors from escaping into the atmosphere. The purge valve is connected to the canister, which stores these vapors until they can be burned off when you start the engine. Over time, the clips that hold the purge valve in place can become loose and fall off.

If this happens, your car will not be able to properly release fuel vapors and will fail an emissions test. Here’s how to remove the purge valve clips so you can get your car back on the road.

  • Remove the negative battery cable from the battery terminal
  • Unplug the vacuum hose from the purge valve assembly
  • Using a small flat-blade screwdriver, remove the two retaining clips from the bottom of the valve housing
  • Carefully pull the valve out of the housing and discard it
  • Install a new valve in the housing and secure it with the retaining clips
  • Reconnect the vacuum hose to the purge valve assembly and install 7the negative battery cable on 8the battery terminal

Vapor Canister Purge Valve Hose Clip

The vapor canister purge valve hose clip is a small, but important, part of your car’s emission control system. The clip helps to secure the vapor canister purge valve hose to the vapor canister, and prevents the hose from becoming disconnected. If the vapor canister purge valve hose becomes disconnected, it can cause your car to fail an emissions test, or produce excess emissions.

The vapor canister purge valve hose clip is made of metal, and is usually silver in color. It is located on the back of the vapor canister purge valve, and is held in place by a retaining ring. The retaining ring is also made of metal, and snaps into place over the clip.

To remove the retaining ring and clip, you will need a pair of pliers. Once you have removed the retaining ring and clip, you can disconnect the vapor canister purge valve hose from the vapor canister. To do this, simply pull on the hose until it comes loose from the fitting on the vapor canister.

You may need to wiggle it back-and-forth a bit to get it started, but it should come loose relatively easily. If you are replacing the entire Vapor Canister Purge Valve Hose assembly, then you will also need to replace the O-ring that seals between the Vapor Canister Purge Valve andthe evaporative emission (EVAP)canISTER . The O-ring is located onthe underside ofthe Vapor CanISTER PURGE VALVE ASSEMBLY ,andis available separately as part# 90467-07158 .

How Do You Remove a Ford Purge Valve Clip?

If you need to remove the purge valve clip on your Ford vehicle, there are a few things you’ll need to do. First, locate the purge valve itself. It’s usually located on or near the throttle body.

Once you’ve found it, disconnect the vacuum line that’s attached to it. Next, use a pair of pliers to remove the spring clip that holds the valve in place. Be careful not to lose this clip, as you’ll need it when reinstalling the valve.

Finally, pull out the valve and discard it.

How Do You Remove an Evap Line from a Clip?

There are a few different ways that you can remove an EVAP line from a clip. The first way is to use a pair of pliers. Simply grip the line with the pliers and pull it out of the clip.

Another way is to use a small screwdriver. Insert the screwdriver into the top of the clip and pry it open. Then, you can wiggle the line out of the clip.

Finally, if you have a sharp knife, you can carefully insert it into the side of the clip and cut through the line. Whichever method you choose, be careful not to damage either the clip or the line itself.

How Do You Remove a Purge Valve Solenoid?

Assuming you are asking about a purge valve solenoid on a vehicle: The purge valve solenoid is located on the evaporative canister, and is usually attached to the canister with two screws. In order to remove it, you will need to unscrew these screws and then detach the electrical connector from the solenoid.

Can You Replace Purge Valve Yourself?

Yes, you can replace the purge valve yourself. The process is not difficult, but there are a few things you need to know before starting. The first thing you need to do is locate the purge valve.

This is usually located near the firewall on the driver’s side of the vehicle. Once you have found it, you will need to disconnect the vacuum line that goes to it. You can do this by simply pulling on the line until it comes off.

Next, you will need to remove the two bolts that hold the purge valve in place. Once these are removed, you can pull out the old valve and insert the new one. Be sure to align it correctly so that it seats properly, then replace the bolts and reconnect the vacuum line.

That’s all there is to it! Replacing your purge valve is a simple process that anyone can do with just a few tools.


Removing purge valve clips may seem like a daunting task, but it’s actually quite simple. All you need is a flat head screwdriver and a little patience. Start by prying up one end of the clip with your screwdriver.

Once the clip is loose, slide it off of the valve stem. Repeat this process for the other clip. With both clips removed, the purge valve should now be free.

You can now proceed to clean or replace the valve as needed.

Leave a Comment

Your email address will not be published. Required fields are marked *