If you’re like most people, you probably don’t think about your brakes until there’s a problem. But brake pads don’t last forever, and they need to be replaced periodically. You can usually tell when they need to be replaced because the brake pedal will feel softer than usual or the car will pull to one side when you brake.
If you’re not sure how to tell if your brake pads need replacing, consult your Silverado’s owner’s manual. The process for resetting the brake pad monitor is different for 2019 Silverado’s than it is for older models, so be sure to follow the instructions carefully.
- Park your vehicle in a safe and level location
- Apply the parking brake and chock the rear wheels to prevent the truck from rolling while you’re working
- Locate the fuse panel under the dash on the driver’s side of the truck and remove the fuse for “Brake Lights
- Disconnect the negative (-) battery cable to disable any power going to your truck while you’re working
- Remove the two bolts holding each caliper in place with a wrench or socket set, then pull the caliper off of the rotor
- Suspend each caliper from its respective brake line using a wire hanger or similar device to prevent damage to the lines while you work (see photo)
- Use a C-clamp or similar device to compress each piston back into its bore until it is flush with the surface of the caliper housing (see photo)
- Be sure not to damage any surfaces during this process as it may cause brake fluid leaks later on down the road With both pistons compressed, remove the old brake pads from their retaining clips inside the caliper housing and discard them properly
- Install the new brake pads into their retaining clips, making sure they are seated correctly
- Release the C-clamp or other compression device slowly to allow each piston to return to its original position within its bore
- Reattach each caliper assembly to its respective rotor using the bolts you removed earlier, then torque them down according to your truck’s specifications
- Reconnect the negative (-) battery cable and reinstall the “Brake Lights” fuse in the panel under the dash
How to Reset Brake Pad Monitor 2019 Gmc Sierra
If you’re like most GMC Sierra owners, you probably don’t think much about your truck’s brake system. But it’s important to keep an eye on your brake pads and make sure they’re in good condition. If they wear down too much, it could lead to expensive repairs.
The good news is that there’s a easy way to check the condition of your brake pads: the Brake Pad Monitor (BPM). This system uses sensors to monitor the thickness of your brake pads and will warn you when they’re getting low. Here’s how to reset the BPM on your 2019 GMC Sierra:
1. Start the engine and let it idle for a few minutes.
2. Press the “Info” button on the instrument cluster until you see “Vehicle Info” on the display.
3. Scroll down to “Brake Pad Monitor.” It should say “OFF.”
4. Press and hold the “Set/Reset” button for five seconds or until you see “ON.” The BPM is now reset and will start monitoring your brake pads again.
How Do You Reset the Brake Monitor on a 2019 Silverado?
Assuming you would like a blog post discussing how to reset the brake monitor on a 2019 Silverado:
If your 2019 Silverado is equipped with brake monitoring, you may need to reset the system after replacing the brakes. Here’s how to do it:
Locate the button for the brake monitor on the dash. It may be labeled “Brake Monitor” or have a symbol of a circle with an exclamation point inside. Press and hold this button for three seconds.
The system will chime and the message “Brake Monitor Reset” should display on the dash. Release the button and press it again for three seconds. The system will chime again and the message “Brake Monitor Learn Mode Active” should display.
This means that the system is now in learn mode and is ready to relearn your driving habits. Drive normally for at least two days, making sure to use both city streets and highways. After two days, press and hold the button again for three seconds.
The system will chime once more and “Brake Monitor Ready” should appear on the dash, indicating that the relearning process is complete.
How Do I Reset My Brake Pad Wear Indicator?
Brake pad wear indicators are designed to give drivers a warning when their brake pads have worn down to a certain point. When the brake pad wear indicator contacts the rotor, it makes a squealing noise that alerts the driver that the brakes need to be serviced.
To reset the brake pad wear indicator, you will need to remove the old brake pads and install new ones.
Once the new brake pads are in place, you can use a small piece of metal or a nail to push the reset button on the back of the caliper.
How Do You Put Brake Aid Mode in 2019 Silverado?
Assuming you are referring to the Brake Assist feature on the 2019 Silverado:
To turn on Brake Assist, press and hold the brake pedal while you start the engine. When you release the brake pedal, Brake Assist remains active.
To turn off Brake Assist, do one of the following:
• Press and hold the brake pedal until you see BRAKE ASSIST OFF in the Driver Information Center (DIC).
• Turn off the vehicle.
How Do You Reset the Brake Life on a 2021 Silverado?
Assuming you would like a step-by-step guide on resetting the brake life on a 2021 Silverado:
1. To begin, open the hood and locate the fuse box.
2. Find the fuse labeled “ESC” and remove it using a pair of needle nose pliers.
3. With the fuse removed, press and hold the brake pedal for approximately 15 seconds.
4. Next, turn the key to the “On” position without starting the engine. Once again, press and hold the brake pedal for 15 seconds.
5. Finally, reinsert the ESC fuse and close the hood.
Conclusion
If your 2019 Silverado’s brake pad monitor is giving you trouble, don’t worry – it can be reset easily. All you need to do is follow these simple steps in the above We discussed.
