How to Reset Pats System Ford F150

In order to reset the PATS system on a Ford F150, you will need to have the ignition key that came with the vehicle. If you do not have this key, you will need to get a new one from a Ford dealership. Once you have the key, insert it into the ignition and turn it to the “On” position.

Then, press and hold the trip odometer button for approximately five seconds. This will cause the system to enter into what is called “learning mode.” At this point, you can start your engine and drive as normal.

  • First, locate the Pats system module, which is usually found under the hood on the driver’s side of the vehicle
  • Next, disconnect the negative battery cable from the module
  • Once the negative battery cable is disconnected, remove the fuse for the Pats system
  • With the fuse removed, press and hold down the reset button for the Pats system for about 30 seconds
  • After 30 seconds have passed, release the button and then reinstall both the fuse and negative battery cable back to their respective places

Ford F150 Theft Light Blinking Won’T Start

If your Ford F-150’s theft light is blinking and the vehicle won’t start, there are a few things you can do to try and troubleshoot the issue. First, check to see if the battery is dead or if there’s another problem with the electrical system. If everything looks good there, then it’s time to move on to checking the starter and ignition system.

If those components are working properly, then it’s likely that the issue lies with the anti-theft system itself. There are a few ways to reset the system, so be sure to consult your owner’s manual for specific instructions. With any luck, one of these methods will get your truck up and running again in no time.

How to Reset Pats System Ford F150


How Long Does It Take for the Anti-Theft System to Reset?

An anti-theft system, also known as an immobilizer, is a device that prevents your car from being started without the proper key. Most modern cars have some form of anti-theft system, and they can be incredibly effective at deterring thieves. However, if you lose your key or accidentally trigger the alarm, it can be very frustrating trying to get the system reset.

So how long does it take for the anti-theft system to reset? The answer depends on the make and model of your car, as well as the type of anti-theft system that is installed. Some systems can be reset relatively quickly, while others may take a few days.

If you need to get your car’s anti-theft systemreset, the best thing to do is contact your local dealership or locksmith. They will have the specific knowledge and tools needed to reset the system correctly.

Can Ford Disable Pats System?

Most newer Ford vehicles are equipped with a Passive Anti-Theft System (PATS). This system uses a transponder key embedded with a computer chip that sends a signal to the vehicle, allowing it to start. If an attempt is made to start the vehicle without the key, or if the wrong key is used, the engine will not start.

While this system is effective at deterring theft, there may be times when you need to disable it. Here are some instructions on how to do so. 1. Locate the PATS module.

This is usually found in the central junction box under the dash, but its location can vary depending on the make and model of your vehicle. 2. Disconnect the battery negative terminal for 30 seconds then reconnect it. This will reset all PATS parameters and disable the system.

3. Locate the two wires that go to pin 7 of the PATS module connector – these will be labeled “P” and “B” for programming and bypass, respectively. Cut or disconnect these wires then reconnect them together using a wire connector or splice them together with solder and electrical tape. This will bypass the PATS system entirely.

How Do You Reprogram Pats?

When it comes to reprogramming Pats, there are a few different ways that you can go about doing so. One of the most popular methods is to use a software program called “Pat programmer”. This particular software is designed specifically for programming and controlling Pat robots.

It allows you to create custom programs for your robot, as well as change existing programs that are already installed on your robot. Another method that you can use to reprogram Pats is by using a physical remote control. This option gives you the ability to directly input commands into your robot, without having to go through any type of programming interface.

While this method may be slightly less user-friendly than using software, it can still be quite effective if you know what you’re doing. Finally, if you want to completely remove all programming from your Pat robot, then you can always reset it back to its factory settings. This will erase all of the programs and settings that have been stored on your robot, allowing you to start from scratch again.

Keep in mind though that this should only be done as a last resort, as it will completely wipe out everything that has been programmed into your Pat robot up until this point.

How Do I Get My Car Out of Anti-Theft Mode?

If your car has an anti-theft device, you may be wondering how to get it out of that mode. Here are a few steps to take: 1. Find the anti-theft device.

This is usually located near the ignition or steering column. 2. Enter the code into the device. The code should be given to you when you bought the car or it may be in your owner’s manual.

3. If the code doesn’t work, try pressing and holding the reset button for a few seconds. This should disable the anti-theft mode. 4. If all else fails, consult your owner’s manual or contact a professional for assistance.

1999 Ford F-150 code 11 anti-theft fix


If your truck is acting up and you think it may be the Pats system, there are a few things you can try to reset it. First, disconnect the negative battery cable for about five minutes. This will reset the computer and clear any codes that may have been set off.

If that doesn’t work, you can also try disconnecting the positive battery cable for about thirty seconds. This will also reset the computer but will also erase all of your stored data, so make sure to back everything up first! If neither of these work, then it’s time to take it to a mechanic or Ford dealership to have them take a look at it.

Leave a Comment

Your email address will not be published. Required fields are marked *