How to Reset Thermometer in Dodge Ram

There are a few different ways that you can reset the thermometer in your Dodge Ram. One way is to simply disconnect the battery for a few minutes and then reconnect it. This will cause the computer to reset and the thermometer should go back to normal.

Another way is to remove the fuse for the instrument panel cluster for a few seconds and then put it back in. This should also reset the thermometer. If neither of these methods work, then you may need to take your vehicle to a dealer or mechanic to have them reset the thermometer for you.

  • Park the Dodge Ram in a level area
  • Turn off the engine and set the parking brake
  • Locate the thermostat housing on the engine
  • It is on the upper radiator hose, near the firewall on the driver’s side of the engine compartment
  • Use a flathead screwdriver to remove the two screws that secure the housing to the hose
  • Pull off the housing and discard it
  • Take out the old thermostat from its location in the housing bore
  • Inspect it for cracks or other damage, and replace it if necessary
  • Coat the new thermostat with a light layer of automotive silicone sealant and insert it into place in the bore, making sure that it is fully seated against its gasket surface
  • 6 Clean off any excess sealant around
  • the perimeter of

2014 Ram Ambient Temp Sensor Location

As the weather starts to get warmer, it’s important to be aware of your vehicle’s ambient temperature sensor and its location. The 2014 Ram 1500 has an ambient temperature sensor located in the front grille. This sensor helps the truck’s computer system determine the outside air temperature, which is used to adjust the cabin temperature accordingly.

If you’re having trouble with your truck’s AC not cooling properly, this is one possible reason why. You can check if the sensor is working by starting the engine and turning on the AC. Then, feel around the front grille for a small metal disc – this is your ambient temp sensor.

If it feels cool to the touch, then it’s probably working fine. However, if it feels warm or hot, then it may be malfunctioning and needs to be replaced.

How to Reset Thermometer in Dodge Ram


How Do I Reset My Temperature Sensor?

The temperature sensor is an important part of your car’s engine management system. It helps the computer to adjust the fuel mixture and ignition timing for optimal performance and efficiency. If your temperature sensor is not working properly, it can cause your engine to run lean or rich, resulting in reduced performance and fuel economy.

In extreme cases, it can even cause engine damage. If you think your temperature sensor may be malfunctioning, the first step is to check the fuse. If the fuse is blown, replace it with a new one and see if that fixes the problem.

If not, then you will need to check the wiring harness for any loose, broken or damaged wires. Once you have confirmed that everything is in good working order, you can reset the sensor by disconnecting the battery for 30 seconds.

Why is My Car Reading the Wrong Temperature?

If your car is reading the wrong temperature, there are a few possible reasons. One possibility is that the sensor is damaged or dirty and needs to be replaced or cleaned. Another possibility is that the cooling system is not working properly and needs to be repaired.

Finally, it could be that the software in your car’s computer system needs to be updated. If you’re not sure what the problem is, it’s best to take your car to a mechanic for diagnosis and repair.

Where is the Outside Temperature Sensor on a Dodge Ram?

The outside temperature sensor on a Dodge Ram is located in the grille, just behind the front bumper. It is used to measure the ambient air temperature and send a signal to the onboard computer. This information is then used by the computer to adjust the engine’s operating parameters accordingly.

Why Does My Car Say Its Negative 40 Degrees?

If your car is displaying a negative temperature, there are a few potential explanations. In most cases, it’s simply an error and the sensor needs to be reset. However, in some cases it could indicate a problem with the cooling system.

One possibility is that the coolant level is low. If the coolant level is too low, it can cause the engine to overheat. This will trigger the temperature gauge to display a negative reading.

Another possibility is that there is a leak in the cooling system. A leak can cause the coolant level to drop and also trigger the temperature gauge to display a negative reading. If your car’s temperature gauge is displaying a negative reading, it’s best to have it checked out by a mechanic as soon as possible.

They’ll be able to diagnose the problem and get your car running smoothly again.

How To Fix Inaccurate Outside Temp Readings On A 2018 Ram 2500


If your Dodge Ram’s thermometer is reading inaccurately, you can reset it by following these steps: 1.Turn the ignition off and wait a few seconds. 2.Turn the ignition back on without starting the engine. 3.Wait for the chimes to stop, then press and hold the “trip” button until the odometer displays “P.” 4.Release the button and press it again until you see “PCM?” 5.Release the button and turn the key to the “off” position.

6.Remove the key from the ignition and insert it into the door lock cylinder on the driver’s side door. 7.Turn clockwise until you hear a click, then counterclockwise for two clicks (this will unlock your vehicle). 8.Insert your key into the ignition and turn to “on” without starting your engine 9..

Press and release gas pedal three times within five seconds 10,.Wait seven seconds 11,.Start your engine 12,.

Leave a Comment

Your email address will not be published. Required fields are marked *