How to Turn on Rear Speakers in Suburban

If your vehicle is equipped with rear speakers and you’re not hearing sound from them, there are a few things you can check. First, make sure that the balance on your stereo is set evenly between the front and rear speakers. If it’s not, adjust it until you do hear sound coming from the back.

Next, check to see if your car has an “fade” setting; if so, make sure it’s not turned all the way to the front or back. Finally, take a look at your vehicle’s wiring to see if anything looks loose or damaged.

  • Open the rear door of the Suburban
  • Locate the two screws on the top edge of the speaker paneling
  • Unscrew these two screws using a Phillips head screwdriver and pull off the speaker paneling
  • Find the wire harnesses connected to the back of each speaker and make sure they are plugged in securely
  • Replace the speaker paneling and screw it back into place with the two screws you removed earlier
  • Close the rear door of the Suburban

Suburban Rear Speakers Not Working

If your suburban rear speakers are not working, there are a few things that could be causing the problem. First, check to see if the speakers are properly plugged in. If they are, then the next thing to check is the fuse.

The fuse may be blown and need to be replaced. Finally, check the wiring to see if it is loose or damaged.

Why are My Rear Speakers Not Playing?

If your car has a factory stereo, the most common reason why your rear speakers might not be playing is because there’s a problem with the amplifier. The amplifier provides power to all the speakers in your car, so if it’s not working properly, none of the speakers will play sound. There are a few other possibilities as well.

If you have aftermarket speakers or an aftermarket stereo, it’s possible that they’re not wired correctly. Or, there could be a problem with the speaker itself. In any case, troubleshooting speaker problems can be tricky, so it’s always best to consult with a professional if you’re having trouble getting your audio system to work properly.

Why Do My Rear Speakers Not Have Sound in My Car?

If you’re experiencing sound issues with your car’s rear speakers, there are a few potential causes. First, check to make sure that the speakers are turned on and that the volume is set properly. If they’re turned off or the volume is set too low, you won’t be able to hear anything coming from the speakers.

If the speakers are turned on and the volume is set correctly but you still can’t hear anything, it’s possible that there’s an issue with the speaker itself. Try testing the speaker by plugging it into another device, such as a stereo system or portable speaker. If it works fine when plugged into another device, then there may be something wrong with your car’s audio system.

Another potential cause of sound issues with rear speakers is a blown fuse. Check your car’s owner manual to locate the fuse box and see if any of the fuses related to the audio system have blown. If so, replace them with new fuses and see if that fixes the problem.

Why are My Door Speakers Not Working?

One of the most common reasons why door speakers may stop working is because of a blown fuse. If your car’s door speakers are not working, check the fuse box for a blown fuse. You can usually find the fuse box under the hood or in the driver’s side footwell.

Once you’ve found the fuse box, check to see if any of the fuses are burned out or broken. If so, replace them with new fuses of the same amperage. Another reason why your door speakers might not be working is because of a loose wire connection.

Over time, wires can become loose due to vibrations from driving. To check for loose wire connections, first make sure that all of the speaker wires are securely connected to both the speakers and the head unit. If they appear to be tight, then use a multimeter to test for continuity between each wire terminal and its corresponding speaker connector.

If there is no continuity, then you’ll need to splice in new wire to establish a connection. If your car’s door speakers still aren’t working after checking for blown fuses and loose wire connections, then it’s possible that the problem lies with one or more of the components within the speaker itself. The most likely culprits are eitherthe voice coil orthe spider assembly.

To test whether these parts are defective, you’ll need to use an ohmmeter to measure resistance across them (between + and -). A healthy voice coil should have a resistance reading of around 4 ohms, whereas a defective one will typically have much higher resistance readings (10 ohms or more).

What is Rear in Speaker?

If you’re a music lover, you know that the quality of your sound system is important. But what exactly is rear in speaker? Rear in speaker refers to the speakers that are placed behind the listener.

These speakers create a surround sound effect that makes it feel like you’re in the middle of the action. This type of speaker setup is ideal for movies and video games because it creates an immersive experience. However, rear in speaker can also be used for music listening.

When used for this purpose, they can provide a more spacious and three-dimensional soundscape. This can make your music listening experience more enjoyable as you feel like you’re inside the music rather than just hearing it from one direction. If you’re looking to improve your home theater or music listening setup, consider adding some rear in speakers to your system!


If your Chevy Suburban is equipped with rear speakers and you’re not hearing any sound coming from them, there are a few things you can check to see if they’re turned on. First, look for a button labeled “Rear” or “Rear Speaker” on your radio. If this button is lit up, it means the rear speakers are turned on.

If the button is not lit up, press it to turn on the rear speakers. Another way to tell if the rear speakers are turned on is by looking at the balance control knob on your radio. This knob determines how much sound comes out of the left and right speakers.

If the knob is all the way to the left or right, that means no sound will be coming out of the opposite side’s speaker. So, if your balance knob is all the way to the left, that means no sound will be coming out of the right speaker – including any rear speakers that may be connected to it. To fix this, simply adjust the balance knob until you can hear sound coming from both sides evenly.

Leave a Comment

Your email address will not be published. Required fields are marked *