What Does Trailer Brake Module Fault Mean

What Does Trailer Brake Module Fault Mean

If you’re towing a trailer and your brake controller starts displaying a trailer brake module fault, it can be frustrating not knowing what the problem is. Is it a simple fix or something more serious? This guide will help you understand what a trailer brake module fault means and what you can do about it.

If you’re like most people, you’ve probably never heard of a trailer brake module. But if you own a vehicle that tows a trailer, it’s an important part of your safety system. A trailer brake module is a computer that controls the electric brakes on your trailer.

If it senses that the trailer is starting to fishtail or otherwise lose control, it will automatically apply the brakes to help stabilize the situation. However, sometimes these modules can fail, resulting in what’s known as a “trailer brake module fault.” This can be extremely dangerous, as it means that your trailer’s brakes may not work when you need them most.

If you’re experiencing a trailer brake module fault, the best thing to do is to take your vehicle to a qualified mechanic or dealership for diagnosis and repair. In the meantime, be sure to drive carefully and avoid any situations where you might need to rely on your trailer’s brakes.

Trailer Brake Module Fault Ford F250

If you have a Ford F250 with a trailer brake module fault, there are a few things you can do to troubleshoot the problem. First, check the fuses and circuit breakers associated with the trailer brakes. Next, check the wiring harness for any loose or damaged wires.

Finally, inspect the trailer brake module itself for any damage or corrosion. If you find that the fuse or circuit breaker is blown, replace it with a new one and see if that fixes the problem. If the wiring harness is damaged, you may need to replace it entirely.

And if you find damage or corrosion on the trailer brake module itself, it will need to be replaced as well. With any luck, one of these three troubleshooting tips will help you fix your trailer brake module fault and get your Ford F250 back on the road again!

How Do You Reprogram a Trailer Brake Control Module?

If your trailer brake control module isn’t working properly, you may need to reprogram it. Here’s how to do it:

1. Start by disconnecting the battery from the module. This will help prevent any accidental shorts while you’re working.

2. Next, remove the cover from the module so you can access the circuit board inside.

3. Locate the small microprocessor chip on the board and carefully remove it.
4. Install a new microprocessor chip in its place and reattach the cover to the module.

5. Reconnect the battery to the module and test it out to see if it’s working properly now.

What Does It Mean When Your Car Says Trailer Brake System?

When your car says “trailer brake system,” it means that the vehicle is equipped with a braking system specifically designed for use with a trailer. This type of system is typically found on larger vehicles, such as SUVs and trucks. The trailer brake system allows the driver to apply the brakes on the trailer without affecting the brakes on the vehicle itself.

This can be useful when hauling a large or heavy load, as it allows for greater control over braking. The trailer brake system is typically activated by a switch located in the cab of the vehicle, and may also be controlled by a separate set of pedals or levers.

How Do You Test a Brake Control Module?

A brake control module is an important part of a vehicle’s braking system. It controls the amount of pressure that is applied to the brakes when the pedal is depressed. If there is a problem with the brake control module, it can cause problems with the braking system, which can lead to accidents.

There are several ways to test a brake control module.

  • One way is to use a voltmeter to check for voltage at the module’s connector while the engine is running. The voltmeter should register around 12 volts if the module is functioning properly.
  • Another way to test the brake control module is to use an ohmmeter to check for continuity between the two terminals on the connector. The resistance should be low if the module is functioning properly. If either of these tests indicates a problem with the brake control module, it should be replaced as soon as possible. A faulty brake control module can cause serious problems with a vehicle’s braking system and should not be ignored.


If you have a trailer brake module fault, it means that there is an issue with the electronic control unit for your trailer brakes. This can be caused by a number of things, including a short circuit, loose connection, or damaged wiring. If you have this fault, it’s important to get it fixed as soon as possible so that your trailer brakes will work properly.

Leave a Comment

Your email address will not be published. Required fields are marked *