Why is My Abs Light on After Changing Wheel Bearing

My ABS light being on after changing the wheel bearing could be due to a variety of different issues. If the new wheel bearing was installed incorrectly, it may cause premature wear and trigger an ABS fault code. It is also possible that the Anti-lock Braking System (ABS) sensor or tone ring for the affected wheel has become damaged during installation and needs to be replaced.

Additionally, if dirt or debris enters into any of the brake system components when installing a new wheel bearing this can also set off an ABS warning light. Lastly, there could have been damage to some of wiring associated with either the tone ring or ABS circuit which would require further diagnosis from a qualified mechanic.

If your ABS light is on after changing a wheel bearing, it could indicate that the new bearing was installed incorrectly or without properly lubricating the parts. It can also mean that there is an issue with something else in the system such as a faulty sensor or wiring problem. If you suspect any of these issues, make sure to take your vehicle to a qualified mechanic for further analysis and repair.

Reset Abs Warning Light After Repair

After completing a repair on your vehicle, it is important to reset the ABS warning light. To do this, turn off the ignition and disconnect the battery for 10 minutes before reconnecting it. After that, start the engine and check if the ABS warning light stays off – if not, repeat these steps one more time until the light goes away.

Why is My Abs Light on After Changing Wheel Bearing

Credit: www.brakeandfrontend.com

Can a New Wheel Bearing Cause the Abs Light to Come On?

The answer to this question is yes, a new wheel bearing can cause the ABS light to come on. This is because the ABS system in your vehicle relies on sensors located at each wheel that measure wheel speed. If one of these sensors isn’t working properly or has been damaged, then your ABS light will illuminate as a warning sign that there may be an issue with the brakes.

When replacing a wheel bearing, it’s important to make sure all components of the braking system are inspected and replaced if needed. The new wheel bearing should also be checked for proper fitment before installation and correctly torqued down during installation process so that it doesn’t get misaligned or move out of its position over time which could also trigger an ABS fault code. Additionally, while replacing any part related to braking system such as rotors, calipers etc., it is always recommended to check for any signs of wear & tear in other parts too like brake pads, hoses etc., which can lead to increased friction between them leading again into triggering the ABS light on your dashboard.

How Do You Reset the Abs Light Sensor?

Resetting the ABS light sensor is an important part of maintaining your vehicle’s anti-lock braking system. The light will come on if there are any problems with the ABS, so it’s important to reset the light as soon as possible in order to keep your brakes working properly. Resetting the ABS light involves a few easy steps: first, find the fuse box under your dashboard and locate the specific fuse for your ABS system; second, turn off that fuse and wait at least 10 seconds before turning it back on; finally, start up your car again and see if the warning lights have gone out.

If they haven’t, you may need more in-depth repairs or adjustments done by a certified mechanic. Taking care of this issue promptly can help avoid further damage or costly repairs down road.

Can a Wheel Bearing Affect the Abs Sensor?

Yes, a wheel bearing can affect the ABS sensor. The ABS sensor senses how fast each wheel is spinning and sends signals to the ABS system when it detects any variation in speed or changes in direction. If one of your wheel bearings has worn out, then this may cause misreadings from the ABS sensors as they are detecting different speeds for each wheel due to the imbalance created by an old or damaged bearing.

This could result in poor brake performance and even dangerous situations if you don’t repair it as soon as possible. Additionally, because most vehicles now have traction control systems that rely on information from both the wheels and brakes, having an inaccurate or faulty wheel bearing will not only affect your braking capabilities but also your vehicle’s overall stability while driving on slippery surfaces. Therefore, it is important to inspect all four of your vehicle’s wheel bearings regularly to ensure that everything is working properly and no damage has been sustained by them over time.

How Do You Reset Abs And Traction Control Light?

If you’ve noticed the ABS and traction control light illuminate on your dashboard, it can be a bit alarming. Thankfully, resetting these lights is relatively straightforward and doesn’t involve any major repairs. To reset the ABS and traction control light, start by turning off your car’s engine.

Then open the hood of your vehicle to locate the fuse box. Remove both of the ABS fuses located in this box – they are usually labeled as such – using either a pair of pliers or tweezers if necessary. Allow these fuses to sit for about 10 minutes before replacing them securely into their respective slots in the fuse box.

Once done, close up everything around your vehicle’s engine bay before testing out whether or not you have successfully reset your car’s ABS and traction control light system by starting up the ignition again; if successful, both those lights should now be off!

Abs light on after new wheel bearing


In conclusion, the most likely cause of an ABS light coming on after changing a wheel bearing is that the sensor in the bearing wiring has been damaged. It is important to make sure that all connections are securely fastened and that any new sensors or wires are properly installed before replacing a wheel bearing. Taking these precautions can help prevent further issues with your vehicle’s ABS system down the road.

Leave a Comment

Your email address will not be published. Required fields are marked *